Opencoil/electronics: Difference between revisions

From Teilen macht Spass!
Jump to navigation Jump to search
No edit summary
No edit summary
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
# opencoil-paracity: electronics






https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/esp-wireless-charging-pcb/pcb-ass.jpg
https://wiki.teilenmachtspass.lol/customcontent/pcb-ass.jpg


*Assembled pcb*
*Assembled pcb*
Line 25: Line 24:
You need to desolder two IC's/ chips following the (visual) guide below. The electronics and coil are sandwiched between two layers of foil. To peel the foil away look for an opening near the lightning connector.
You need to desolder two IC's/ chips following the (visual) guide below. The electronics and coil are sandwiched between two layers of foil. To peel the foil away look for an opening near the lightning connector.


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/001-coil.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/001-coil.jpg


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/002-peel.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/002-peel.jpg


You are then left over with the bare coil and flexible pcb. Here I already desoldered the lightning connector flex pcb.
You are then left over with the bare coil and flexible pcb. Here I already desoldered the lightning connector flex pcb.


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/003-bare-coil.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/003-bare-coil.jpg




Line 38: Line 37:
* Q4 (chip markings: wsc7)
* Q4 (chip markings: wsc7)


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/004-q3.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/004-q3.jpg
![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/005-q4.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/005-q4.jpg


A hot air reworking station + tweezers will make quick work of that (settings: 1 second on 320deg, moderate airflow). Without hot-air you could try a soldering iron or fine wire-cutters to simply cut away the chips. The flexible PCB is very fragile though.
A hot air reworking station + tweezers will make quick work of that (settings: 1 second on 320deg, moderate airflow). Without hot-air you could try a soldering iron or fine wire-cutters to simply cut away the chips. The flexible PCB is very fragile though.


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/006-hotair.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/006-hotair.jpg


Step 1 completed!
Step 1 completed!


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/007-hotair-done.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/007-hotair-done.jpg


### Step 2
### Step 2
Line 53: Line 52:
With both chips removed, you have to bridge two of the three (now) bare connections of the transistor Q4. I could not find a datasheet on this transistor so please refer to the photo's to see which pins.
With both chips removed, you have to bridge two of the three (now) bare connections of the transistor Q4. I could not find a datasheet on this transistor so please refer to the photo's to see which pins.


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/008-bridge.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/008-bridge.jpg


Done!
Done!


![picture](https://git.vvvvvvaria.org/then/opencoil-paracity/raw/branch/master/electronics/coil-mod/009-done.jpg)
https://wiki.teilenmachtspass.lol/customcontent/coil-mod/009-done.jpg

Latest revision as of 20:43, 28 August 2022


pcb-ass.jpg

  • Assembled pcb*
    1. Bill of Materials
    • NOTE**: Be aware that these 'adaptor coils' could contain additional circuitry that condition the output for use with specific mobile phones (the pearl.de ones do). Below is a guide to modify the 'pearl' coils to deliver maximum voltage (5v)constantly, instead of switching to low power, 2.5v output when not enough/too much current is drawn.


    1. Modding 'adaptor coils'

If you have soldered all components together and your ESP12f won't boot, you might have to modify your charging coil+circuit a bit. To make sure it's the coil, measure the output of the coil's electronics on the + and - (GND) terminals. If your multimeter reads ~2.5 volts you need to modify the circuit. (Disclaimer: the exact details on how this circuit works are yet unclear, comparing to a working coil revealed several differences in the electronics, matching them up made the non working coil output the needed 5v).

      1. Step 1

You need to desolder two IC's/ chips following the (visual) guide below. The electronics and coil are sandwiched between two layers of foil. To peel the foil away look for an opening near the lightning connector.

001-coil.jpg

002-peel.jpg

You are then left over with the bare coil and flexible pcb. Here I already desoldered the lightning connector flex pcb.

003-bare-coil.jpg


Remove the following chips indicated by the following silkscreen printing:

  • Q3 (chip markings: p7)
  • Q4 (chip markings: wsc7)

004-q3.jpg 005-q4.jpg

A hot air reworking station + tweezers will make quick work of that (settings: 1 second on 320deg, moderate airflow). Without hot-air you could try a soldering iron or fine wire-cutters to simply cut away the chips. The flexible PCB is very fragile though.

006-hotair.jpg

Step 1 completed!

007-hotair-done.jpg

      1. Step 2

With both chips removed, you have to bridge two of the three (now) bare connections of the transistor Q4. I could not find a datasheet on this transistor so please refer to the photo's to see which pins.

008-bridge.jpg

Done!

009-done.jpg